LGD/hand_control
1
0
Fork 0
Code Issues Pull requests Releases Wiki Activity
hand_control/README-en.md

6.5 KiB
Raw Blame History

Installation

This package was developped with the Indigo version of ROS.

Dependencies installation

#!sh
sudo sh -c 'echo "deb http://packages.ros.org/ros/ubuntu trusty main" > /etc/apt/sources.list.d/ros-latest.list'
wget https://raw.githubusercontent.com/ros/rosdistro/master/ros.key -O - | sudo apt-key add -
sudo apt-get update
sudo apt-get install ros-indigo-desktop-full ros-indigo-freenect-stack ros-indigo-ardrone-autonomy libncursesw5-dev

Package installation

Catkin workspace creation

For instance :

#!sh
source /opt/ros/indigo/setup.bash
mkdir -p ~/hand_control_ws/src
cd ~/hand_control_ws/src
catkin_init_workspace

Code location

If necessary, rename the folder with the file named hand_control, and move it in ~/hand_control_ws/src/ or in the subfolder src of your catkin workspace.

Compilation

You're now able to compile :

#!sh
cd ~/hand_control_ws # or your catkin workspace
catkin_make

Then you can run the following commands to be able to use the ROS commands. If necessary replace "hand_control_ws" by the name of your catkin workspace.

#!sh
source /opt/ros/indigo/setup.bash
source ~/hand_control_ws/devel/setup.bash
echo "source /opt/ros/indigo/setup.bash" >> ~/.bashrc
echo "source ~/hand_control_ws/devel/setup.bash" >> ~/.bashrc

Use

Connection and setting up of the Kinect

  1. Connect the Kinect (under voltage) to the computer via USB ;
  2. Put the Kinect on the ground, pointed toward the roof ; be aware that your arm must be perpendicular to the Kinect in order to control the drone properly ;
  3. Launch the "launchfile" kinect_commander.launch : roslaunch hand_control kinect_commander.launch ;
  4. Check the drone parameters :
    • launch rviz : rosrun rqt_rviz rqt_rviz
    • display the output of the filtering (topic : /filter/output ; frame : /camera_depth_optical_frame) and locate the hand ;
    • launch rqt_reconfigure : rosrun rqt_reconfigure rqt_reconfigure in order to :
      • change the filter parameters until you only see the points of the hand/glove/panel on rviz (see above).
      • change the parameter neutral_alt of the node commander to the wanted height (in meters), correponding to the height of the hand for which the height of the drone will be stable.

Parameters of the filter

The parameters of the filter (that can be changed thanks to dynamic_reconfigure and in particular rqt_reconfigure) are :

  • z_max : in meters, maximal height of the hand. It must be lower than the height of the roof.
  • for a glove or a colored panel (green, blue, etc.), we generaly have :
    • hue : for example 220 (sky blue) or 150 (green) or 0 (pink/red) ;
    • delta_hue : between 10 and 20 ;
    • sat/val_min : 0.0 ;
    • sat/val_max : 1.0 ;
  • pour un gant noir :
    • hue : 0 ;
    • delta_hue : 180 ;
    • sat_min : 0.0 ;
    • sat_max : 1.0 ;
    • val_min : 0.0 ;
    • val_max : 0.3 (at your convenience);

Other parameters

Always with rqt_reconfigure, but with the estimator node :

  • reverse : swap x and y, the axes of the Kinect (default : false, ie. unchecked)
  • reverse_angle : change the angle choosen for the compute of the angle of the hand (default : false, ie. unchecked)

Connection to the drone and steering

  • Connect the computer to the wifi network of the drone ;
  • Launch the "launchfile" ardrone.launch : roslaunch hand_control ardrone.launch ;
  • Taking of :
    • whether rostopic pub /ardrone/takeoff std_msgs/Empty ;
    • or launch the node keyboard_cmd : rosrun hand_control keyboard_cmd and use t on the keyboard.
  • Landing :
    • whether rostopic pub /ardrone/land std_msgs/Empty ;
    • or, launch the node keyboard_cmd, and use b on the keyboard.
  • Emergency stop :
    • whether rostopic pub /ardrone/reset std_msgs/Empty ;
    • or, launch the node keyboard_cmd, and use g on the keyboard.

Hand steering

  • Forward/Reverse & side translations : hand tilt ;
  • Rotate (around the vertical axis z) : angle of the hand with the the axis parallel to the ground and perpendicular to the kinect ;
  • Climb/Descend : hand height.

Options and parameters of the command

To edit the options of the command, change (if not already) rosrun rqt_reconfigure rqt_reconfigure :

  • max_curvature : not used today ;
  • x/y/z/theta_minimal_deviation : thresholds required above which the movement of the hand is not taken into account. If all are 0.0, the drone responds linearly.
    • x, y : between 0. and 1. (corresponding to the x and y of the normal to the plane);
    • z : in meters ;
    • theta : in degrees.
  • neutral_alt : height of the hand for the immobility of the height of the drone ;
  • min_points_number : minimal number of points (for the point cloud used for the regression) necessary in order to send a command to the drone ;
  • angle/x/y/z_vel : proportionality coefficients to apply to the inputs in order to establish the command sent to the drone. Increase it will increase the speed of the drone ;
  • up_fact : proportionality coefficients to apply to the command that increases the height of the drone, compared to the equivalent command to reduce it (in order to correct the effect of gravity).

About keyboard_cmd

It allows you to publish commands on the topic cmd_vel and so to steer the drone. It is scheduled for azerty keyboards. To launch it, run :

#!sh
rosrun hand_control keyboard_cmd

To increase/decrease the speed (there is an explication on the controlpanel) : a,z,e,r and w,x,c,v

The informations of the drone are updated when a key is pressed.

To quit : CTRL+C and press "Enter" to return to the console.

Problems - Possible improvements

  • Si des commandes sont publiées sur cmd_vel (depuis la Kinect par exemple) après le lancement du fichier ardrone.launch et avant le décollage du drone, alors, après le décollage, de drone semble obéir aux commandes publiées avant le décollage.

  • Comme écrit plus haut, l’affichage des informations reçues du drone sur keyboard_cmd n’est mise à jour qu’à l’occasion de l’appui sur une touche, et peut donc rester fixe quand on n’utilise pas la commande au clavier.

  • Le décollage/atterrissage n’est pas possible à commander avec la main. Il faut utiliser le clavier (keyboard_cmd ou rostopic pub) à la place. Il est possible de de remédier à cela en créant deux nouveaux seuils, minimaux et maximaux, pour la hauteur de la main : une main très basse ferait atterrir le drone, une main très haute le ferait décoller.