rezometz/re2o
8
0
Fork 0
mirror of https://gitlab.federez.net/re2o/re2o synced 2024-05-19 00:52:52 +00:00
Code Issues Releases Wiki Activity

Ajout des fichiers d'exemple et de conf pour freeradius

Browse source
This commit is contained in:
Gabriel Detraz 2017-09-19 00:08:52 +00:00 committed by root
parent b53c502498
commit 8156cb68f7
4 changed files with 2275 additions and 0 deletions
Show stats Download patch file Download diff file Expand all files Collapse all files

873
freeradius_utils/freeradius3/mods-enabled/eap Normal file
View file

@ -0,0 +1,873 @@
# -*- text -*-
##
## eap.conf -- Configuration for EAP types (PEAP, TTLS, etc.)
##
## $Id: 0e8d5caef5ad09dfa6acb14c5d475bae55cf4b27 $
#######################################################################
#
# Whatever you do, do NOT set 'Auth-Type := EAP'. The server
# is smart enough to figure this out on its own. The most
# common side effect of setting 'Auth-Type := EAP' is that the
# users then cannot use ANY other authentication method.
#
eap {
# Invoke the default supported EAP type when
# EAP-Identity response is received.
#
# The incoming EAP messages DO NOT specify which EAP
# type they will be using, so it MUST be set here.
#
# For now, only one default EAP type may be used at a time.
#
# If the EAP-Type attribute is set by another module,
# then that EAP type takes precedence over the
# default type configured here.
#
default_eap_type = md5
# A list is maintained to correlate EAP-Response
# packets with EAP-Request packets. After a
# configurable length of time, entries in the list
# expire, and are deleted.
#
timer_expire = 60
# There are many EAP types, but the server has support
# for only a limited subset. If the server receives
# a request for an EAP type it does not support, then
# it normally rejects the request. By setting this
# configuration to "yes", you can tell the server to
# instead keep processing the request. Another module
# MUST then be configured to proxy the request to
# another RADIUS server which supports that EAP type.
#
# If another module is NOT configured to handle the
# request, then the request will still end up being
# rejected.
ignore_unknown_eap_types = no
# Cisco AP1230B firmware 12.2(13)JA1 has a bug. When given
# a User-Name attribute in an Access-Accept, it copies one
# more byte than it should.
#
# We can work around it by configurably adding an extra
# zero byte.
cisco_accounting_username_bug = no
#
# Help prevent DoS attacks by limiting the number of
# sessions that the server is tracking. For simplicity,
# this is taken from the "max_requests" directive in
# radiusd.conf.
max_sessions = ${max_requests}
# Supported EAP-types
#
# We do NOT recommend using EAP-MD5 authentication
# for wireless connections. It is insecure, and does
# not provide for dynamic WEP keys.
#
md5 {
}
#
# EAP-pwd -- secure password-based authentication
#
# pwd {
# group = 19
#
# server_id = theserver@example.com
# This has the same meaning as for TLS.
# fragment_size = 1020
# The virtual server which determines the
# "known good" password for the user.
# Note that unlike TLS, only the "authorize"
# section is processed. EAP-PWD requests can be
# distinguished by having a User-Name, but
# no User-Password, CHAP-Password, EAP-Message, etc.
# virtual_server = "inner-tunnel"
# }
# Cisco LEAP
#
# We do not recommend using LEAP in new deployments. See:
# http://www.securiteam.com/tools/5TP012ACKE.html
#
# Cisco LEAP uses the MS-CHAP algorithm (but not
# the MS-CHAP attributes) to perform it's authentication.
#
# As a result, LEAP *requires* access to the plain-text
# User-Password, or the NT-Password attributes.
# 'System' authentication is impossible with LEAP.
#
leap {
}
# Generic Token Card.
#
# Currently, this is only permitted inside of EAP-TTLS,
# or EAP-PEAP. The module "challenges" the user with
# text, and the response from the user is taken to be
# the User-Password.
#
# Proxying the tunneled EAP-GTC session is a bad idea,
# the users password will go over the wire in plain-text,
# for anyone to see.
#
gtc {
# The default challenge, which many clients
# ignore..
#challenge = "Password: "
# The plain-text response which comes back
# is put into a User-Password attribute,
# and passed to another module for
# authentication. This allows the EAP-GTC
# response to be checked against plain-text,
# or crypt'd passwords.
#
# If you say "Local" instead of "PAP", then
# the module will look for a User-Password
# configured for the request, and do the
# authentication itself.
#
auth_type = PAP
}
## Common TLS configuration for TLS-based EAP types
#
# See raddb/certs/README for additional comments
# on certificates.
#
# If OpenSSL was not found at the time the server was
# built, the "tls", "ttls", and "peap" sections will
# be ignored.
#
# If you do not currently have certificates signed by
# a trusted CA you may use the 'snakeoil' certificates.
# Included with the server in raddb/certs.
#
# If these certificates have not been auto-generated:
# cd raddb/certs
# make
#
# These test certificates SHOULD NOT be used in a normal
# deployment. They are created only to make it easier
# to install the server, and to perform some simple
# tests with EAP-TLS, TTLS, or PEAP.
#
# See also:
#
# http://www.dslreports.com/forum/remark,9286052~mode=flat
#
# Note that you should NOT use a globally known CA here!
# e.g. using a Verisign cert as a "known CA" means that
# ANYONE who has a certificate signed by them can
# authenticate via EAP-TLS! This is likely not what you want.
tls-config tls-common {
private_key_password = whatever
private_key_file = /etc/ssl/private/ssl-cert-snakeoil.key
# If Private key & Certificate are located in
# the same file, then private_key_file &
# certificate_file must contain the same file
# name.
#
# If ca_file (below) is not used, then the
# certificate_file below MUST include not
# only the server certificate, but ALSO all
# of the CA certificates used to sign the
# server certificate.
certificate_file = /etc/ssl/certs/ssl-cert-snakeoil.pem
# Trusted Root CA list
#
# ALL of the CA's in this list will be trusted
# to issue client certificates for authentication.
#
# In general, you should use self-signed
# certificates for 802.1x (EAP) authentication.
# In that case, this CA file should contain
# *one* CA certificate.
#
ca_file = /etc/ssl/certs/ca-certificates.crt
# OpenSSL will automatically create certificate chains,
# unless we tell it to not do that. The problem is that
# it sometimes gets the chains right from a certificate
# signature view, but wrong from the clients view.
#
# When setting "auto_chain = no", the server certificate
# file MUST include the full certificate chain.
# auto_chain = yes
#
# If OpenSSL supports TLS-PSK, then we can use
# a PSK identity and (hex) password. When the
# following two configuration items are specified,
# then certificate-based configuration items are
# not allowed. e.g.:
#
# private_key_password
# private_key_file
# certificate_file
# ca_file
# ca_path
#
# For now, the identity is fixed, and must be the
# same on the client. The passphrase must be a hex
# value, and can be up to 256 hex digits.
#
# Future versions of the server may be able to
# look up the shared key (hexphrase) based on the
# identity.
#
# psk_identity = "test"
# psk_hexphrase = "036363823"
#
# For DH cipher suites to work, you have to
# run OpenSSL to create the DH file first:
#
# openssl dhparam -out certs/dh 2048
#
dh_file = ${certdir}/dh
#
# If your system doesn't have /dev/urandom,
# you will need to create this file, and
# periodically change its contents.
#
# For security reasons, FreeRADIUS doesn't
# write to files in its configuration
# directory.
#
# random_file = /dev/urandom
#
# This can never exceed the size of a RADIUS
# packet (4096 bytes), and is preferably half
# that, to accommodate other attributes in
# RADIUS packet. On most APs the MAX packet
# length is configured between 1500 - 1600
# In these cases, fragment size should be
# 1024 or less.
#
# fragment_size = 1024
# include_length is a flag which is
# by default set to yes If set to
# yes, Total Length of the message is
# included in EVERY packet we send.
# If set to no, Total Length of the
# message is included ONLY in the
# First packet of a fragment series.
#
# include_length = yes
# Check the Certificate Revocation List
#
# 1) Copy CA certificates and CRLs to same directory.
# 2) Execute 'c_rehash <CA certs&CRLs Directory>'.
# 'c_rehash' is OpenSSL's command.
# 3) uncomment the lines below.
# 5) Restart radiusd
# check_crl = yes
# Check if intermediate CAs have been revoked.
# check_all_crl = yes
ca_path = ${cadir}
#
# If check_cert_issuer is set, the value will
# be checked against the DN of the issuer in
# the client certificate. If the values do not
# match, the certificate verification will fail,
# rejecting the user.
#
# In 2.1.10 and later, this check can be done
# more generally by checking the value of the
# TLS-Client-Cert-Issuer attribute. This check
# can be done via any mechanism you choose.
#
# check_cert_issuer = "/C=GB/ST=Berkshire/L=Newbury/O=My Company Ltd"
#
# If check_cert_cn is set, the value will
# be xlat'ed and checked against the CN
# in the client certificate. If the values
# do not match, the certificate verification
# will fail rejecting the user.
#
# This check is done only if the previous
# "check_cert_issuer" is not set, or if
# the check succeeds.
#
# In 2.1.10 and later, this check can be done
# more generally by checking the value of the
# TLS-Client-Cert-CN attribute. This check
# can be done via any mechanism you choose.
#
# check_cert_cn = %{User-Name}
#
# Set this option to specify the allowed
# TLS cipher suites. The format is listed
# in "man 1 ciphers".
#
# For EAP-FAST, use "ALL:!EXPORT:!eNULL:!SSLv2"
#
cipher_list = "DEFAULT"
# Work-arounds for OpenSSL nonsense
# OpenSSL 1.0.1f and 1.0.1g do not calculate
# the EAP keys correctly. The fix is to upgrade
# OpenSSL, or disable TLS 1.2 here.
#
# For EAP-FAST, this MUST be set to "yes".
#
# disable_tlsv1_2 = no
#
#
# Elliptical cryptography configuration
#
# Only for OpenSSL >= 0.9.8.f
#
ecdh_curve = "prime256v1"
#
# Session resumption / fast reauthentication
# cache.
#
# The cache contains the following information:
#
# session Id - unique identifier, managed by SSL
# User-Name - from the Access-Accept
# Stripped-User-Name - from the Access-Request
# Cached-Session-Policy - from the Access-Accept
#
# The "Cached-Session-Policy" is the name of a
# policy which should be applied to the cached
# session. This policy can be used to assign
# VLANs, IP addresses, etc. It serves as a useful
# way to re-apply the policy from the original
# Access-Accept to the subsequent Access-Accept
# for the cached session.
#
# On session resumption, these attributes are
# copied from the cache, and placed into the
# reply list.
#
# You probably also want "use_tunneled_reply = yes"
# when using fast session resumption.
#
cache {
#
# Enable it. The default is "no". Deleting the entire "cache"
# subsection also disables caching.
#
# You can disallow resumption for a particular user by adding the
# following attribute to the control item list:
#
# Allow-Session-Resumption = No
#
# If "enable = no" below, you CANNOT enable resumption for just one
# user by setting the above attribute to "yes".
#
enable = yes
#
# Lifetime of the cached entries, in hours. The sessions will be
# deleted/invalidated after this time.
#
lifetime = 24 # hours
#
# The maximum number of entries in the
# cache. Set to "0" for "infinite".
#
# This could be set to the number of users
# who are logged in... which can be a LOT.
#
max_entries = 255
#
# Internal "name" of the session cache. Used to
# distinguish which TLS context sessions belong to.
#
# The server will generate a random value if unset.
# This will change across server restart so you MUST
# set the "name" if you want to persist sessions (see
# below).
#
#name = "EAP module"
#
# Simple directory-based storage of sessions.
# Two files per session will be written, the SSL
# state and the cached VPs. This will persist session
# across server restarts.
#
# The server will need write perms, and the directory
# should be secured from anyone else. You might want
# a script to remove old files from here periodically:
#
# find ${logdir}/tlscache -mtime +2 -exec rm -f {} \;
#
# This feature REQUIRES "name" option be set above.
#
#persist_dir = "${logdir}/tlscache"
}
#
# As of version 2.1.10, client certificates can be
# validated via an external command. This allows
# dynamic CRLs or OCSP to be used.
#
# This configuration is commented out in the
# default configuration. Uncomment it, and configure
# the correct paths below to enable it.
#
# If OCSP checking is enabled, and the OCSP checks fail,
# the verify section is not run.
#
# If OCSP checking is disabled, the verify section is
# run on successful certificate validation.
#
verify {
# If the OCSP checks succeed, the verify section
# is run to allow additional checks.
#
# If you want to skip verify on OCSP success,
# uncomment this configuration item, and set it
# to "yes".
# skip_if_ocsp_ok = no
# A temporary directory where the client
# certificates are stored. This directory
# MUST be owned by the UID of the server,
# and MUST not be accessible by any other
# users. When the server starts, it will do
# "chmod go-rwx" on the directory, for
# security reasons. The directory MUST
# exist when the server starts.
#
# You should also delete all of the files
# in the directory when the server starts.
# tmpdir = /tmp/radiusd
# The command used to verify the client cert.
# We recommend using the OpenSSL command-line
# tool.
#
# The ${..ca_path} text is a reference to
# the ca_path variable defined above.
#
# The %{TLS-Client-Cert-Filename} is the name
# of the temporary file containing the cert
# in PEM format. This file is automatically
# deleted by the server when the command
# returns.
# client = "/path/to/openssl verify -CApath ${..ca_path} %{TLS-Client-Cert-Filename}"
}
#
# OCSP Configuration
# Certificates can be verified against an OCSP
# Responder. This makes it possible to immediately
# revoke certificates without the distribution of
# new Certificate Revocation Lists (CRLs).
#
ocsp {
#
# Enable it. The default is "no".
# Deleting the entire "ocsp" subsection
# also disables ocsp checking
#
enable = no
#
# The OCSP Responder URL can be automatically
# extracted from the certificate in question.
# To override the OCSP Responder URL set
# "override_cert_url = yes".
#
override_cert_url = yes
#
# If the OCSP Responder address is not extracted from
# the certificate, the URL can be defined here.
#
url = "http://127.0.0.1/ocsp/"
#
# If the OCSP Responder can not cope with nonce
# in the request, then it can be disabled here.
#
# For security reasons, disabling this option
# is not recommended as nonce protects against
# replay attacks.
#
# Note that Microsoft AD Certificate Services OCSP
# Responder does not enable nonce by default. It is
# more secure to enable nonce on the responder than
# to disable it in the query here.
# See http://technet.microsoft.com/en-us/library/cc770413%28WS.10%29.aspx
#
# use_nonce = yes
#
# Number of seconds before giving up waiting
# for OCSP response. 0 uses system default.
#
# timeout = 0
#
# Normally an error in querying the OCSP
# responder (no response from server, server did
# not understand the request, etc) will result in
# a validation failure.
#
# To treat these errors as 'soft' failures and
# still accept the certificate, enable this
# option.
#
# Warning: this may enable clients with revoked
# certificates to connect if the OCSP responder
# is not available. Use with caution.
#
# softfail = no
}
}
## EAP-TLS
#
# As of Version 3.0, the TLS configuration for TLS-based
# EAP types is above in the "tls-config" section.
#
tls {
# Point to the common TLS configuration
tls = tls-common
#
# As part of checking a client certificate, the EAP-TLS
# sets some attributes such as TLS-Client-Cert-CN. This
# virtual server has access to these attributes, and can
# be used to accept or reject the request.
#
# virtual_server = check-eap-tls
}
## EAP-TTLS
#
# The TTLS module implements the EAP-TTLS protocol,
# which can be described as EAP inside of Diameter,
# inside of TLS, inside of EAP, inside of RADIUS...
#
# Surprisingly, it works quite well.
#
ttls {
# Which tls-config section the TLS negotiation parameters
# are in - see EAP-TLS above for an explanation.
#
# In the case that an old configuration from FreeRADIUS
# v2.x is being used, all the options of the tls-config
# section may also appear instead in the 'tls' section
# above. If that is done, the tls= option here (and in
# tls above) MUST be commented out.
#
tls = tls-common
# The tunneled EAP session needs a default EAP type
# which is separate from the one for the non-tunneled
# EAP module. Inside of the TTLS tunnel, we recommend
# using EAP-MD5. If the request does not contain an
# EAP conversation, then this configuration entry is
# ignored.
#
default_eap_type = md5
# The tunneled authentication request does not usually
# contain useful attributes like 'Calling-Station-Id',
# etc. These attributes are outside of the tunnel,
# and normally unavailable to the tunneled
# authentication request.
#
# By setting this configuration entry to 'yes',
# any attribute which is NOT in the tunneled
# authentication request, but which IS available
# outside of the tunnel, is copied to the tunneled
# request.
#
# allowed values: {no, yes}
#
copy_request_to_tunnel = yes
#
# As of version 3.0.5, this configuration item
# is deprecated. Instead, you should use
#
# update outer.session-state {
# ...
#
# }
#
# This will cache attributes for the final Access-Accept.
#
# The reply attributes sent to the NAS are usually
# based on the name of the user 'outside' of the
# tunnel (usually 'anonymous'). If you want to send
# the reply attributes based on the user name inside
# of the tunnel, then set this configuration entry to
# 'yes', and the reply to the NAS will be taken from
# the reply to the tunneled request.
#
# allowed values: {no, yes}
#
use_tunneled_reply = no
#
# The inner tunneled request can be sent
# through a virtual server constructed
# specifically for this purpose.
#
# If this entry is commented out, the inner
# tunneled request will be sent through
# the virtual server that processed the
# outer requests.
#
virtual_server = "inner-tunnel"
# This has the same meaning, and overwrites, the
# same field in the "tls" configuration, above.
# The default value here is "yes".
#
# include_length = yes
#
# Unlike EAP-TLS, EAP-TTLS does not require a client
# certificate. However, you can require one by setting the
# following option. You can also override this option by
# setting
#
# EAP-TLS-Require-Client-Cert = Yes
#
# in the control items for a request.
#
# require_client_cert = yes
}
## EAP-PEAP
#
##################################################
#
# !!!!! WARNINGS for Windows compatibility !!!!!
#
##################################################
#
# If you see the server send an Access-Challenge,
# and the client never sends another Access-Request,
# then
#
# STOP!
#
# The server certificate has to have special OID's
# in it, or else the Microsoft clients will silently
# fail. See the "scripts/xpextensions" file for
# details, and the following page:
#
# http://support.microsoft.com/kb/814394/en-us
#
# For additional Windows XP SP2 issues, see:
#
# http://support.microsoft.com/kb/885453/en-us
#
#
# If is still doesn't work, and you're using Samba,
# you may be encountering a Samba bug. See:
#
# https://bugzilla.samba.org/show_bug.cgi?id=6563
#
# Note that we do not necessarily agree with their
# explanation... but the fix does appear to work.
#
##################################################
#
# The tunneled EAP session needs a default EAP type
# which is separate from the one for the non-tunneled
# EAP module. Inside of the TLS/PEAP tunnel, we
# recommend using EAP-MS-CHAPv2.
#
peap {
# Which tls-config section the TLS negotiation parameters
# are in - see EAP-TLS above for an explanation.
#
# In the case that an old configuration from FreeRADIUS
# v2.x is being used, all the options of the tls-config
# section may also appear instead in the 'tls' section
# above. If that is done, the tls= option here (and in
# tls above) MUST be commented out.
#
tls = tls-common
# The tunneled EAP session needs a default
# EAP type which is separate from the one for
# the non-tunneled EAP module. Inside of the
# PEAP tunnel, we recommend using MS-CHAPv2,
# as that is the default type supported by
# Windows clients.
#
default_eap_type = mschapv2
# The PEAP module also has these configuration
# items, which are the same as for TTLS.
#
copy_request_to_tunnel = yes
#
# As of version 3.0.5, this configuration item
# is deprecated. Instead, you should use
#
# update outer.session-state {
# ...
#
# }
#
# This will cache attributes for the final Access-Accept.
#
use_tunneled_reply = no
# When the tunneled session is proxied, the
# home server may not understand EAP-MSCHAP-V2.
# Set this entry to "no" to proxy the tunneled
# EAP-MSCHAP-V2 as normal MSCHAPv2.
#
# proxy_tunneled_request_as_eap = yes
#
# The inner tunneled request can be sent
# through a virtual server constructed
# specifically for this purpose.
#
# If this entry is commented out, the inner
# tunneled request will be sent through
# the virtual server that processed the
# outer requests.
#
virtual_server = "inner-tunnel"
# This option enables support for MS-SoH
# see doc/SoH.txt for more info.
# It is disabled by default.
#
# soh = yes
#
# The SoH reply will be turned into a request which
# can be sent to a specific virtual server:
#
# soh_virtual_server = "soh-server"
#
# Unlike EAP-TLS, PEAP does not require a client certificate.
# However, you can require one by setting the following
# option. You can also override this option by setting
#
# EAP-TLS-Require-Client-Cert = Yes
#
# in the control items for a request.
#
# require_client_cert = yes
}
#
# This takes no configuration.
#
# Note that it is the EAP MS-CHAPv2 sub-module, not
# the main 'mschap' module.
#
# Note also that in order for this sub-module to work,
# the main 'mschap' module MUST ALSO be configured.
#
# This module is the *Microsoft* implementation of MS-CHAPv2
# in EAP. There is another (incompatible) implementation
# of MS-CHAPv2 in EAP by Cisco, which FreeRADIUS does not
# currently support.
#
mschapv2 {
# Prior to version 2.1.11, the module never
# sent the MS-CHAP-Error message to the
# client. This worked, but it had issues
# when the cached password was wrong. The
# server *should* send "E=691 R=0" to the
# client, which tells it to prompt the user
# for a new password.
#
# The default is to behave as in 2.1.10 and
# earlier, which is known to work. If you
# set "send_error = yes", then the error
# message will be sent back to the client.
# This *may* help some clients work better,
# but *may* also cause other clients to stop
# working.
#
# send_error = no
# Server identifier to send back in the challenge.
# This should generally be the host name of the
# RADIUS server. Or, some information to uniquely
# identify it.
# identity = "FreeRADIUS"
}
## EAP-FAST
#
# The FAST module implements the EAP-FAST protocol
#
# fast {
# Point to the common TLS configuration
#
# cipher_list though must include "ADH" for anonymous provisioning.
# This is not as straight forward as appending "ADH" alongside
# "DEFAULT" as "DEFAULT" contains "!aNULL" so instead it is
# recommended "ALL:!EXPORT:!eNULL:!SSLv2" is used
#
# tls = tls-common
# PAC lifetime in seconds (default: seven days)
#
# pac_lifetime = 604800
# Authority ID of the server
#
# if you are running a cluster of RADIUS servers, you should make
# the value chosen here (and for "pac_opaque_key") the same on all
# your RADIUS servers. This value should be unique to your
# installation. We suggest using a domain name.
#
# authority_identity = "1234"
# PAC Opaque encryption key (must be exactly 32 bytes in size)
#
# This value MUST be secret, and MUST be generated using
# a secure method, such as via 'openssl rand -hex 32'
#
# pac_opaque_key = "0123456789abcdef0123456789ABCDEF"
# Same as for TTLS, PEAP, etc.
#
# virtual_server = inner-tunnel
# }
}

818
freeradius_utils/freeradius3/radiusd.conf Normal file
View file

@ -0,0 +1,818 @@
# -*- text -*-
##
## radiusd.conf -- FreeRADIUS server configuration file - 3.0.12
##
## http://www.freeradius.org/
## $Id: c62f4ffed53a073a885f243b728129f5c482fad7 $
##
######################################################################
#
# Read "man radiusd" before editing this file. See the section
# titled DEBUGGING. It outlines a method where you can quickly
# obtain the configuration you want, without running into
# trouble.
#
# Run the server in debugging mode, and READ the output.
#
# $ radiusd -X
#
# We cannot emphasize this point strongly enough. The vast
# majority of problems can be solved by carefully reading the
# debugging output, which includes warnings about common issues,
# and suggestions for how they may be fixed.
#
# There may be a lot of output, but look carefully for words like:
# "warning", "error", "reject", or "failure". The messages there
# will usually be enough to guide you to a solution.
#
# If you are going to ask a question on the mailing list, then
# explain what you are trying to do, and include the output from
# debugging mode (radiusd -X). Failure to do so means that all
# of the responses to your question will be people telling you
# to "post the output of radiusd -X".
######################################################################
#
# The location of other config files and logfiles are declared
# in this file.
#
# Also general configuration for modules can be done in this
# file, it is exported through the API to modules that ask for
# it.
#
# See "man radiusd.conf" for documentation on the format of this
# file. Note that the individual configuration items are NOT
# documented in that "man" page. They are only documented here,
# in the comments.
#
# The "unlang" policy language can be used to create complex
# if / else policies. See "man unlang" for details.
#
prefix = /usr
exec_prefix = /usr
sysconfdir = /etc
localstatedir = /var
sbindir = ${exec_prefix}/sbin
logdir = /var/log/freeradius
raddbdir = /etc/freeradius/3.0
radacctdir = ${logdir}/radacct
#
# name of the running server. See also the "-n" command-line option.
name = freeradius
# Location of config and logfiles.
confdir = ${raddbdir}
modconfdir = ${confdir}/mods-config
certdir = ${confdir}/certs
cadir = ${confdir}/certs
run_dir = ${localstatedir}/run/${name}
# Should likely be ${localstatedir}/lib/radiusd
db_dir = ${raddbdir}
#
# libdir: Where to find the rlm_* modules.
#
# This should be automatically set at configuration time.
#
# If the server builds and installs, but fails at execution time
# with an 'undefined symbol' error, then you can use the libdir
# directive to work around the problem.
#
# The cause is usually that a library has been installed on your
# system in a place where the dynamic linker CANNOT find it. When
# executing as root (or another user), your personal environment MAY
# be set up to allow the dynamic linker to find the library. When
# executing as a daemon, FreeRADIUS MAY NOT have the same
# personalized configuration.
#
# To work around the problem, find out which library contains that symbol,
# and add the directory containing that library to the end of 'libdir',
# with a colon separating the directory names. NO spaces are allowed.
#
# e.g. libdir = /usr/local/lib:/opt/package/lib
#
# You can also try setting the LD_LIBRARY_PATH environment variable
# in a script which starts the server.
#
# If that does not work, then you can re-configure and re-build the
# server to NOT use shared libraries, via:
#
# ./configure --disable-shared
# make
# make install
#
libdir = /usr/lib/freeradius
# pidfile: Where to place the PID of the RADIUS server.
#
# The server may be signalled while it's running by using this
# file.
#
# This file is written when ONLY running in daemon mode.
#
# e.g.: kill -HUP `cat /var/run/radiusd/radiusd.pid`
#
pidfile = ${run_dir}/${name}.pid
#
# correct_escapes: use correct backslash escaping
#
# Prior to version 3.0.5, the handling of backslashes was a little
# awkward, i.e. "wrong". In some cases, to get one backslash into
# a regex, you had to put 4 in the config files.
#
# Version 3.0.5 fixes that. However, for backwards compatibility,
# the new method of escaping is DISABLED BY DEFAULT. This means
# that upgrading to 3.0.5 won't break your configuration.
#
# If you don't have double backslashes (i.e. \\) in your configuration,
# this won't matter to you. If you do have them, fix that to use only
# one backslash, and then set "correct_escapes = true".
#
# You can check for this by doing:
#
# $ grep '\\\\' $(find raddb -type f -print)
#
correct_escapes = true
# panic_action: Command to execute if the server dies unexpectedly.
#
# FOR PRODUCTION SYSTEMS, ACTIONS SHOULD ALWAYS EXIT.
# AN INTERACTIVE ACTION MEANS THE SERVER IS NOT RESPONDING TO REQUESTS.
# AN INTERACTICE ACTION MEANS THE SERVER WILL NOT RESTART.
#
# THE SERVER MUST NOT BE ALLOWED EXECUTE UNTRUSTED PANIC ACTION CODE
# PATTACH CAN BE USED AS AN ATTACK VECTOR.
#
# The panic action is a command which will be executed if the server
# receives a fatal, non user generated signal, i.e. SIGSEGV, SIGBUS,
# SIGABRT or SIGFPE.
#
# This can be used to start an interactive debugging session so
# that information regarding the current state of the server can
# be acquired.
#
# The following string substitutions are available:
# - %e The currently executing program e.g. /sbin/radiusd
# - %p The PID of the currently executing program e.g. 12345
#
# Standard ${} substitutions are also allowed.
#
# An example panic action for opening an interactive session in GDB would be:
#
#panic_action = "gdb %e %p"
#
# Again, don't use that on a production system.
#
# An example panic action for opening an automated session in GDB would be:
#
#panic_action = "gdb -silent -x ${raddbdir}/panic.gdb %e %p 2>&1 | tee ${logdir}/gdb-${name}-%p.log"
#
# That command can be used on a production system.
#
# max_request_time: The maximum time (in seconds) to handle a request.
#
# Requests which take more time than this to process may be killed, and
# a REJECT message is returned.
#
# WARNING: If you notice that requests take a long time to be handled,
# then this MAY INDICATE a bug in the server, in one of the modules
# used to handle a request, OR in your local configuration.
#
# This problem is most often seen when using an SQL database. If it takes
# more than a second or two to receive an answer from the SQL database,
# then it probably means that you haven't indexed the database. See your
# SQL server documentation for more information.
#
# Useful range of values: 5 to 120
#
max_request_time = 30
# cleanup_delay: The time to wait (in seconds) before cleaning up
# a reply which was sent to the NAS.
#
# The RADIUS request is normally cached internally for a short period
# of time, after the reply is sent to the NAS. The reply packet may be
# lost in the network, and the NAS will not see it. The NAS will then
# re-send the request, and the server will respond quickly with the
# cached reply.
#
# If this value is set too low, then duplicate requests from the NAS
# MAY NOT be detected, and will instead be handled as separate requests.
#
# If this value is set too high, then the server will cache too many
# requests, and some new requests may get blocked. (See 'max_requests'.)
#
# Useful range of values: 2 to 10
#
cleanup_delay = 5
# max_requests: The maximum number of requests which the server keeps
# track of. This should be 256 multiplied by the number of clients.
# e.g. With 4 clients, this number should be 1024.
#
# If this number is too low, then when the server becomes busy,
# it will not respond to any new requests, until the 'cleanup_delay'
# time has passed, and it has removed the old requests.
#
# If this number is set too high, then the server will use a bit more
# memory for no real benefit.
#
# If you aren't sure what it should be set to, it's better to set it
# too high than too low. Setting it to 1000 per client is probably
# the highest it should be.
#
# Useful range of values: 256 to infinity
#
max_requests = 16384
# hostname_lookups: Log the names of clients or just their IP addresses
# e.g., www.freeradius.org (on) or 206.47.27.232 (off).
#
# The default is 'off' because it would be overall better for the net
# if people had to knowingly turn this feature on, since enabling it
# means that each client request will result in AT LEAST one lookup
# request to the nameserver. Enabling hostname_lookups will also
# mean that your server may stop randomly for 30 seconds from time
# to time, if the DNS requests take too long.
#
# Turning hostname lookups off also means that the server won't block
# for 30 seconds, if it sees an IP address which has no name associated
# with it.
#
# allowed values: {no, yes}
#
hostname_lookups = no
#
# Logging section. The various "log_*" configuration items
# will eventually be moved here.
#
log {
#
# Destination for log messages. This can be one of:
#
# files - log to "file", as defined below.
# syslog - to syslog (see also the "syslog_facility", below.
# stdout - standard output
# stderr - standard error.
#
# The command-line option "-X" over-rides this option, and forces
# logging to go to stdout.
#
destination = files
#
# Highlight important messages sent to stderr and stdout.
#
# Option will be ignored (disabled) if output if TERM is not
# an xterm or output is not to a TTY.
#
colourise = yes
#
# The logging messages for the server are appended to the
# tail of this file if destination == "files"
#
# If the server is running in debugging mode, this file is
# NOT used.
#
file = ${logdir}/radius.log
#
# If this configuration parameter is set, then log messages for
# a *request* go to this file, rather than to radius.log.
#
# i.e. This is a log file per request, once the server has accepted
# the request as being from a valid client. Messages that are
# not associated with a request still go to radius.log.
#
# Not all log messages in the server core have been updated to use
# this new internal API. As a result, some messages will still
# go to radius.log. Please submit patches to fix this behavior.
#
# The file name is expanded dynamically. You should ONLY user
# server-side attributes for the filename (e.g. things you control).
# Using this feature MAY also slow down the server substantially,
# especially if you do thinks like SQL calls as part of the
# expansion of the filename.
#
# The name of the log file should use attributes that don't change
# over the lifetime of a request, such as User-Name,
# Virtual-Server or Packet-Src-IP-Address. Otherwise, the log
# messages will be distributed over multiple files.
#
# Logging can be enabled for an individual request by a special
# dynamic expansion macro: %{debug: 1}, where the debug level
# for this request is set to '1' (or 2, 3, etc.). e.g.
#
# ...
# update control {
# Tmp-String-0 = "%{debug:1}"
# }
# ...
#
# The attribute that the value is assigned to is unimportant,
# and should be a "throw-away" attribute with no side effects.
#
#requests = ${logdir}/radiusd-%{%{Virtual-Server}:-DEFAULT}-%Y%m%d.log
#
# Which syslog facility to use, if ${destination} == "syslog"
#
# The exact values permitted here are OS-dependent. You probably
# don't want to change this.
#
syslog_facility = daemon
# Log the full User-Name attribute, as it was found in the request.
#
# allowed values: {no, yes}
#
stripped_names = no
# Log authentication requests to the log file.
#
# allowed values: {no, yes}
#
auth = yes
# Log passwords with the authentication requests.
# auth_badpass - logs password if it's rejected
# auth_goodpass - logs password if it's correct
#
# allowed values: {no, yes}
#
auth_badpass = no
auth_goodpass = no
# Log additional text at the end of the "Login OK" messages.
# for these to work, the "auth" and "auth_goodpass" or "auth_badpass"
# configurations above have to be set to "yes".
#
# The strings below are dynamically expanded, which means that
# you can put anything you want in them. However, note that
# this expansion can be slow, and can negatively impact server
# performance.
#
# msg_goodpass = ""
# msg_badpass = ""
# The message when the user exceeds the Simultaneous-Use limit.
#
msg_denied = "You are already logged in - access denied"
}
# The program to execute to do concurrency checks.
checkrad = ${sbindir}/checkrad
# SECURITY CONFIGURATION
#
# There may be multiple methods of attacking on the server. This
# section holds the configuration items which minimize the impact
# of those attacks
#
security {
# chroot: directory where the server does "chroot".
#
# The chroot is done very early in the process of starting
# the server. After the chroot has been performed it
# switches to the "user" listed below (which MUST be
# specified). If "group" is specified, it switches to that
# group, too. Any other groups listed for the specified
# "user" in "/etc/group" are also added as part of this
# process.
#
# The current working directory (chdir / cd) is left
# *outside* of the chroot until all of the modules have been
# initialized. This allows the "raddb" directory to be left
# outside of the chroot. Once the modules have been
# initialized, it does a "chdir" to ${logdir}. This means
# that it should be impossible to break out of the chroot.
#
# If you are worried about security issues related to this
# use of chdir, then simply ensure that the "raddb" directory
# is inside of the chroot, end be sure to do "cd raddb"
# BEFORE starting the server.
#
# If the server is statically linked, then the only files
# that have to exist in the chroot are ${run_dir} and
# ${logdir}. If you do the "cd raddb" as discussed above,
# then the "raddb" directory has to be inside of the chroot
# directory, too.
#
# chroot = /path/to/chroot/directory
# user/group: The name (or #number) of the user/group to run radiusd as.
#
# If these are commented out, the server will run as the
# user/group that started it. In order to change to a
# different user/group, you MUST be root ( or have root
# privileges ) to start the server.
#
# We STRONGLY recommend that you run the server with as few
# permissions as possible. That is, if you're not using
# shadow passwords, the user and group items below should be
# set to radius'.
#
# NOTE that some kernels refuse to setgid(group) when the
# value of (unsigned)group is above 60000; don't use group
# "nobody" on these systems!
#
# On systems with shadow passwords, you might have to set
# 'group = shadow' for the server to be able to read the
# shadow password file. If you can authenticate users while
# in debug mode, but not in daemon mode, it may be that the
# debugging mode server is running as a user that can read
# the shadow info, and the user listed below can not.
#
# The server will also try to use "initgroups" to read
# /etc/groups. It will join all groups where "user" is a
# member. This can allow for some finer-grained access
# controls.
#
user = freerad
group = freerad
# Core dumps are a bad thing. This should only be set to
# 'yes' if you're debugging a problem with the server.
#
# allowed values: {no, yes}
#
allow_core_dumps = no
#
# max_attributes: The maximum number of attributes
# permitted in a RADIUS packet. Packets which have MORE
# than this number of attributes in them will be dropped.
#
# If this number is set too low, then no RADIUS packets
# will be accepted.
#
# If this number is set too high, then an attacker may be
# able to send a small number of packets which will cause
# the server to use all available memory on the machine.
#
# Setting this number to 0 means "allow any number of attributes"
max_attributes = 200
#
# reject_delay: When sending an Access-Reject, it can be
# delayed for a few seconds. This may help slow down a DoS
# attack. It also helps to slow down people trying to brute-force
# crack a users password.
#
# Setting this number to 0 means "send rejects immediately"
#
# If this number is set higher than 'cleanup_delay', then the
# rejects will be sent at 'cleanup_delay' time, when the request
# is deleted from the internal cache of requests.
#
# As of Version 3.0.5, "reject_delay" has sub-second resolution.
# e.g. "reject_delay = 1.4" seconds is possible.
#
# Useful ranges: 1 to 5
reject_delay = 1
#
# status_server: Whether or not the server will respond
# to Status-Server requests.
#
# When sent a Status-Server message, the server responds with
# an Access-Accept or Accounting-Response packet.
#
# This is mainly useful for administrators who want to "ping"
# the server, without adding test users, or creating fake
# accounting packets.
#
# It's also useful when a NAS marks a RADIUS server "dead".
# The NAS can periodically "ping" the server with a Status-Server
# packet. If the server responds, it must be alive, and the
# NAS can start using it for real requests.
#
# See also raddb/sites-available/status
#
status_server = yes
}
# PROXY CONFIGURATION
#
# proxy_requests: Turns proxying of RADIUS requests on or off.
#
# The server has proxying turned on by default. If your system is NOT
# set up to proxy requests to another server, then you can turn proxying
# off here. This will save a small amount of resources on the server.
#
# If you have proxying turned off, and your configuration files say
# to proxy a request, then an error message will be logged.
#
# To disable proxying, change the "yes" to "no", and comment the
# $INCLUDE line.
#
# allowed values: {no, yes}
#
proxy_requests = yes
$INCLUDE proxy.conf
# CLIENTS CONFIGURATION
#
# Client configuration is defined in "clients.conf".
#
# The 'clients.conf' file contains all of the information from the old
# 'clients' and 'naslist' configuration files. We recommend that you
# do NOT use 'client's or 'naslist', although they are still
# supported.
#
# Anything listed in 'clients.conf' will take precedence over the
# information from the old-style configuration files.
#
$INCLUDE clients.conf
# THREAD POOL CONFIGURATION
#
# The thread pool is a long-lived group of threads which
# take turns (round-robin) handling any incoming requests.
#
# You probably want to have a few spare threads around,
# so that high-load situations can be handled immediately. If you
# don't have any spare threads, then the request handling will
# be delayed while a new thread is created, and added to the pool.
#
# You probably don't want too many spare threads around,
# otherwise they'll be sitting there taking up resources, and
# not doing anything productive.
#
# The numbers given below should be adequate for most situations.
#
thread pool {
# Number of servers to start initially --- should be a reasonable
# ballpark figure.
start_servers = 5
# Limit on the total number of servers running.
#
# If this limit is ever reached, clients will be LOCKED OUT, so it
# should NOT BE SET TOO LOW. It is intended mainly as a brake to
# keep a runaway server from taking the system with it as it spirals
# down...
#
# You may find that the server is regularly reaching the
# 'max_servers' number of threads, and that increasing
# 'max_servers' doesn't seem to make much difference.
#
# If this is the case, then the problem is MOST LIKELY that
# your back-end databases are taking too long to respond, and
# are preventing the server from responding in a timely manner.
#
# The solution is NOT do keep increasing the 'max_servers'
# value, but instead to fix the underlying cause of the
# problem: slow database, or 'hostname_lookups=yes'.
#
# For more information, see 'max_request_time', above.
#
max_servers = 32
# Server-pool size regulation. Rather than making you guess
# how many servers you need, FreeRADIUS dynamically adapts to
# the load it sees, that is, it tries to maintain enough
# servers to handle the current load, plus a few spare
# servers to handle transient load spikes.
#
# It does this by periodically checking how many servers are
# waiting for a request. If there are fewer than
# min_spare_servers, it creates a new spare. If there are
# more than max_spare_servers, some of the spares die off.
# The default values are probably OK for most sites.
#
min_spare_servers = 3
max_spare_servers = 10
# When the server receives a packet, it places it onto an
# internal queue, where the worker threads (configured above)
# pick it up for processing. The maximum size of that queue
# is given here.
#
# When the queue is full, any new packets will be silently
# discarded.
#
# The most common cause of the queue being full is that the
# server is dependent on a slow database, and it has received
# a large "spike" of traffic. When that happens, there is
# very little you can do other than make sure the server
# receives less traffic, or make sure that the database can
# handle the load.
#
# max_queue_size = 65536
# There may be memory leaks or resource allocation problems with
# the server. If so, set this value to 300 or so, so that the
# resources will be cleaned up periodically.
#
# This should only be necessary if there are serious bugs in the
# server which have not yet been fixed.
#
# '0' is a special value meaning 'infinity', or 'the servers never
# exit'
max_requests_per_server = 0
# Automatically limit the number of accounting requests.
# This configuration item tracks how many requests per second
# the server can handle. It does this by tracking the
# packets/s received by the server for processing, and
# comparing that to the packets/s handled by the child
# threads.
#
# If the received PPS is larger than the processed PPS, *and*
# the queue is more than half full, then new accounting
# requests are probabilistically discarded. This lowers the
# number of packets that the server needs to process. Over
# time, the server will "catch up" with the traffic.
#
# Throwing away accounting packets is usually safe and low
# impact. The NAS will retransmit them in a few seconds, or
# even a few minutes. Vendors should read RFC 5080 Section 2.2.1
# to see how accounting packets should be retransmitted. Using
# any other method is likely to cause network meltdowns.
#
auto_limit_acct = no
}
######################################################################
#
# SNMP notifications. Uncomment the following line to enable
# snmptraps. Note that you MUST also configure the full path
# to the "snmptrap" command in the "trigger.conf" file.
#
#$INCLUDE trigger.conf
# MODULE CONFIGURATION
#
# The names and configuration of each module is located in this section.
#
# After the modules are defined here, they may be referred to by name,
# in other sections of this configuration file.
#
modules {
#
# Each module has a configuration as follows:
#
# name [ instance ] {
# config_item = value
# ...
# }
#
# The 'name' is used to load the 'rlm_name' library
# which implements the functionality of the module.
#
# The 'instance' is optional. To have two different instances
# of a module, it first must be referred to by 'name'.
# The different copies of the module are then created by
# inventing two 'instance' names, e.g. 'instance1' and 'instance2'
#
# The instance names can then be used in later configuration
# INSTEAD of the original 'name'. See the 'radutmp' configuration
# for an example.
#
#
# As of 3.0, modules are in mods-enabled/. Files matching
# the regex /[a-zA-Z0-9_.]+/ are loaded. The modules are
# initialized ONLY if they are referenced in a processing
# section, such as authorize, authenticate, accounting,
# pre/post-proxy, etc.
#
$INCLUDE mods-enabled/
}
# Instantiation
#
# This section orders the loading of the modules. Modules
# listed here will get loaded BEFORE the later sections like
# authorize, authenticate, etc. get examined.
#
# This section is not strictly needed. When a section like
# authorize refers to a module, it's automatically loaded and
# initialized. However, some modules may not be listed in any
# of the following sections, so they can be listed here.
#
# Also, listing modules here ensures that you have control over
# the order in which they are initialized. If one module needs
# something defined by another module, you can list them in order
# here, and ensure that the configuration will be OK.
#
# After the modules listed here have been loaded, all of the modules
# in the "mods-enabled" directory will be loaded. Loading the
# "mods-enabled" directory means that unlike Version 2, you usually
# don't need to list modules here.
#
instantiate {
#
# We list the counter module here so that it registers
# the check_name attribute before any module which sets
# it
# daily
# subsections here can be thought of as "virtual" modules.
#
# e.g. If you have two redundant SQL servers, and you want to
# use them in the authorize and accounting sections, you could
# place a "redundant" block in each section, containing the
# exact same text. Or, you could uncomment the following
# lines, and list "redundant_sql" in the authorize and
# accounting sections.
#
# The "virtual" module defined here can also be used with
# dynamic expansions, under a few conditions:
#
# * The section is "redundant", or "load-balance", or
# "redundant-load-balance"
# * The section contains modules ONLY, and no sub-sections
# * all modules in the section are using the same rlm_
# driver, e.g. They are all sql, or all ldap, etc.
#
# When those conditions are satisfied, the server will
# automatically register a dynamic expansion, using the
# name of the "virtual" module. In the example below,
# it will be "redundant_sql". You can then use this expansion
# just like any other:
#
# update reply {
# Filter-Id := "%{redundant_sql: ... }"
# }
#
# In this example, the expansion is done via module "sql1",
# and if that expansion fails, using module "sql2".
#
# For best results, configure the "pool" subsection of the
# module so that "retry_delay" is non-zero. That will allow
# the redundant block to quickly ignore all "down" SQL
# databases. If instead we have "retry_delay = 0", then
# every time the redundant block is used, the server will try
# to open a connection to every "down" database, causing
# problems.
#
#redundant redundant_sql {
# sql1
# sql2
#}
}
######################################################################
#
# Policies are virtual modules, similar to those defined in the
# "instantiate" section above.
#
# Defining a policy in one of the policy.d files means that it can be
# referenced in multiple places as a *name*, rather than as a series of
# conditions to match, and actions to take.
#
# Policies are something like subroutines in a normal language, but
# they cannot be called recursively. They MUST be defined in order.
# If policy A calls policy B, then B MUST be defined before A.
#
######################################################################
policy {
$INCLUDE policy.d/
}
######################################################################
#
# Load virtual servers.
#
# This next $INCLUDE line loads files in the directory that
# match the regular expression: /[a-zA-Z0-9_.]+/
#
# It allows you to define new virtual servers simply by placing
# a file into the raddb/sites-enabled/ directory.
#
$INCLUDE sites-enabled/
######################################################################
#
# All of the other configuration sections like "authorize {}",
# "authenticate {}", "accounting {}", have been moved to the
# the file:
#
# raddb/sites-available/default
#
# This is the "default" virtual server that has the same
# configuration as in version 1.0.x and 1.1.x. The default
# installation enables this virtual server. You should
# edit it to create policies for your local site.
#
# For more documentation on virtual servers, see:
#
# raddb/sites-available/README
#
######################################################################

239
freeradius_utils/freeradius3/sites-enabled/default Normal file
View file

@ -0,0 +1,239 @@
######################################################################
#
# As of 2.0.0, FreeRADIUS supports virtual hosts using the
# "server" section, and configuration directives.
#
# Virtual hosts should be put into the "sites-available"
# directory. Soft links should be created in the "sites-enabled"
# directory to these files. This is done in a normal installation.
#
# If you are using 802.1X (EAP) authentication, please see also
# the "inner-tunnel" virtual server. You will likely have to edit
# that, too, for authentication to work.
#
# $Id: 083407596aa5074d665adac9606e7de655b634aa $
#
######################################################################
#
# Read "man radiusd" before editing this file. See the section
# titled DEBUGGING. It outlines a method where you can quickly
# obtain the configuration you want, without running into
# trouble. See also "man unlang", which documents the format
# of this file.
#
# This configuration is designed to work in the widest possible
# set of circumstances, with the widest possible number of
# authentication methods. This means that in general, you should
# need to make very few changes to this file.
#
# The best way to configure the server for your local system
# is to CAREFULLY edit this file. Most attempts to make large
# edits to this file will BREAK THE SERVER. Any edits should
# be small, and tested by running the server with "radiusd -X".
# Once the edits have been verified to work, save a copy of these
# configuration files somewhere. (e.g. as a "tar" file). Then,
# make more edits, and test, as above.
#
# There are many "commented out" references to modules such
# as ldap, sql, etc. These references serve as place-holders.
# If you need the functionality of that module, then configure
# it in radiusd.conf, and un-comment the references to it in
# this file. In most cases, those small changes will result
# in the server being able to connect to the DB, and to
# authenticate users.
#
######################################################################
server default {
listen {
type = auth
ipaddr = *
port = 0
limit {
max_connections = 16
lifetime = 0
idle_timeout = 30
}
}
listen {
ipaddr = *
port = 0
type = acct
limit {
}
}
# IPv6 versions of the above - read their full config to understand options
listen {
type = auth
ipv6addr = :: # any. ::1 == localhost
port = 0
limit {
max_connections = 16
lifetime = 0
idle_timeout = 30
}
}
listen {
ipv6addr = ::
port = 0
type = acct
limit {
}
}
}
server radius-wifi {
authorize {
rewrite_calling_station_id
if (User-Name =~ /^(.*)@(.*)/){
if (User-Name !~ /^(.*)@(.*)example(.*)/){
update control{
Proxy-To-Realm := 'FEDEREZ'
}
}
if ("%{request:User-Name}" =~ /^(.*)@(.*)example(.*)/){
update request{
Stripped-User-Name := "%{1}"
}
}
}
filter_username
preprocess
suffix
eap {
ok = return
}
expiration
logintime
pap
}
authenticate {
Auth-Type PAP {
pap
}
Auth-Type CHAP {
chap
}
Auth-Type MS-CHAP {
mschap
}
mschap
digest
eap
}
preacct {
preprocess
acct_unique
suffix
files
}
accounting {
detail
unix
exec
}
session {
}
post-auth {
update {
&reply: += &session-state:
}
exec
remove_reply_message_if_eap
Post-Auth-Type REJECT {
-sql
attr_filter.access_reject
eap
remove_reply_message_if_eap
}
}
pre-proxy {
}
post-proxy {
eap
}
}
server radius-filaire{
authorize{
re2o
expiration
logintime
pap
}
authenticate{
Auth-Type PAP{
pap
}
Auth-Type CHAP{
chap
}
Auth-Type MS-CHAP{
mschap
}
digest
eap
}
preacct{
preprocess
acct_unique
suffix
files
}
accounting{
}
session{
}
post-auth{
re2o
exec
}
pre-proxy{
}
post-proxy{
eap
}
}

345
freeradius_utils/freeradius3/sites-enabled/inner-tunnel Normal file
View file

@ -0,0 +1,345 @@
# -*- text -*-
######################################################################
#
# This is a virtual server that handles *only* inner tunnel
# requests for EAP-TTLS and PEAP types.
#
# $Id: 2c6f9611bfc7b4b782aeb9764e47e832690739c4 $
#
######################################################################
server inner-tunnel {
#
# This next section is here to allow testing of the "inner-tunnel"
# authentication methods, independently from the "default" server.
# It is listening on "localhost", so that it can only be used from
# the same machine.
#
# $ radtest USER PASSWORD 127.0.0.1:18120 0 testing123
#
# If it works, you have configured the inner tunnel correctly. To check
# if PEAP will work, use:
#
# $ radtest -t mschap USER PASSWORD 127.0.0.1:18120 0 testing123
#
# If that works, PEAP should work. If that command doesn't work, then
#
# FIX THE INNER TUNNEL CONFIGURATION SO THAT IT WORKS.
#
# Do NOT do any PEAP tests. It won't help. Instead, concentrate
# on fixing the inner tunnel configuration. DO NOTHING ELSE.
#
listen {
ipaddr = 127.0.0.1
port = 18120
type = auth
}
# Authorization. First preprocess (hints and huntgroups files),
# then realms, and finally look in the "users" file.
#
# The order of the realm modules will determine the order that
# we try to find a matching realm.
#
# Make *sure* that 'preprocess' comes before any realm if you
# need to setup hints for the remote radius server
authorize {
if ("%{request:User-Name}" =~ /^(.*)@example(.*)/){
update request{
Stripped-User-Name := "%{1}"
}
}
#
# Take a User-Name, and perform some checks on it, for spaces and other
# invalid characters. If the User-Name appears invalid, reject the
# request.
#
# See policy.d/filter for the definition of the filter_username policy.
#
filter_username
re2o
#
# Do checks on outer / inner User-Name, so that users
# can't spoof us by using incompatible identities
#
# filter_inner_identity
#
# The chap module will set 'Auth-Type := CHAP' if we are
# handling a CHAP request and Auth-Type has not already been set
chap
#
# If the users are logging in with an MS-CHAP-Challenge
# attribute for authentication, the mschap module will find
# the MS-CHAP-Challenge attribute, and add 'Auth-Type := MS-CHAP'
# to the request, which will cause the server to then use
# the mschap module for authentication.
mschap
#
# Pull crypt'd passwords from /etc/passwd or /etc/shadow,
# using the system API's to get the password. If you want
# to read /etc/passwd or /etc/shadow directly, see the
# passwd module, above.
#
# unix
#
# Look for IPASS style 'realm/', and if not found, look for
# '@realm', and decide whether or not to proxy, based on
# that.
# IPASS
#
# If you are using multiple kinds of realms, you probably
# want to set "ignore_null = yes" for all of them.
# Otherwise, when the first style of realm doesn't match,
# the other styles won't be checked.
#
# Note that proxying the inner tunnel authentication means
# that the user MAY use one identity in the outer session
# (e.g. "anonymous", and a different one here
# (e.g. "user@example.com"). The inner session will then be
# proxied elsewhere for authentication. If you are not
# careful, this means that the user can cause you to forward
# the authentication to another RADIUS server, and have the
# accounting logs *not* sent to the other server. This makes
# it difficult to bill people for their network activity.
#
suffix
# ntdomain
#
# The "suffix" module takes care of stripping the domain
# (e.g. "@example.com") from the User-Name attribute, and the
# next few lines ensure that the request is not proxied.
#
# If you want the inner tunnel request to be proxied, delete
# the next few lines.
#
update control {
&Proxy-To-Realm := LOCAL
}
#
# This module takes care of EAP-MSCHAPv2 authentication.
#
# It also sets the EAP-Type attribute in the request
# attribute list to the EAP type from the packet.
#
# The example below uses module failover to avoid querying all
# of the following modules if the EAP module returns "ok".
# Therefore, your LDAP and/or SQL servers will not be queried
# for the many packets that go back and forth to set up TTLS
# or PEAP. The load on those servers will therefore be reduced.
#
eap {
ok = return
}
#
# Read the 'users' file
#files
#
# Look in an SQL database. The schema of the database
# is meant to mirror the "users" file.
#
# See "Authorization Queries" in sql.conf
#-sql
#
# If you are using /etc/smbpasswd, and are also doing
# mschap authentication, the un-comment this line, and
# enable the "smbpasswd" module.
# smbpasswd
#
# The ldap module reads passwords from the LDAP database.
#-ldap
#
# Enforce daily limits on time spent logged in.
# daily
expiration
logintime
#
# If no other module has claimed responsibility for
# authentication, then try to use PAP. This allows the
# other modules listed above to add a "known good" password
# to the request, and to do nothing else. The PAP module
# will then see that password, and use it to do PAP
# authentication.
#
# This module should be listed last, so that the other modules
# get a chance to set Auth-Type for themselves.
#
pap
}
# Authentication.
#
#
# This section lists which modules are available for authentication.
# Note that it does NOT mean 'try each module in order'. It means
# that a module from the 'authorize' section adds a configuration
# attribute 'Auth-Type := FOO'. That authentication type is then
# used to pick the appropriate module from the list below.
#
# In general, you SHOULD NOT set the Auth-Type attribute. The server
# will figure it out on its own, and will do the right thing. The
# most common side effect of erroneously setting the Auth-Type
# attribute is that one authentication method will work, but the
# others will not.
#
# The common reasons to set the Auth-Type attribute by hand
# is to either forcibly reject the user, or forcibly accept him.
#
authenticate {
#
# PAP authentication, when a back-end database listed
# in the 'authorize' section supplies a password. The
# password can be clear-text, or encrypted.
Auth-Type PAP {
pap
}
#
# Most people want CHAP authentication
# A back-end database listed in the 'authorize' section
# MUST supply a CLEAR TEXT password. Encrypted passwords
# won't work.
Auth-Type CHAP {
chap
}
#
# MSCHAP authentication.
Auth-Type MS-CHAP {
mschap
}
#
# For old names, too.
#
mschap
#
# Allow EAP authentication.
eap
}
######################################################################
#
# There are no accounting requests inside of EAP-TTLS or PEAP
# tunnels.
#
######################################################################
# Session database, used for checking Simultaneous-Use. Either the radutmp
# or rlm_sql module can handle this.
# The rlm_sql module is *much* faster
session {
radutmp
#
# See "Simultaneous Use Checking Queries" in sql.conf
# sql
}
# Post-Authentication
# Once we KNOW that the user has been authenticated, there are
# additional steps we can take.
#
# Note that the last packet of the inner-tunnel authentication
# MAY NOT BE the last packet of the outer session. So updating
# the outer reply MIGHT work, and sometimes MIGHT NOT. The
# exact functionality depends on both the inner and outer
# authentication methods.
#
# If you need to send a reply attribute in the outer session,
# the ONLY safe way is to set "use_tunneled_reply = yes", and
# then update the inner-tunnel reply.
post-auth {
re2o
Post-Auth-Type REJECT {
# log failed authentications in SQL, too.
-sql
attr_filter.access_reject
#
# Let the outer session know which module failed, and why.
#
update outer.session-state {
&Module-Failure-Message := &request:Module-Failure-Message
}
}
}
#
# When the server decides to proxy a request to a home server,
# the proxied request is first passed through the pre-proxy
# stage. This stage can re-write the request, or decide to
# cancel the proxy.
#
# Only a few modules currently have this method.
#
pre-proxy {
# Uncomment the following line if you want to change attributes
# as defined in the preproxy_users file.
# files
# Uncomment the following line if you want to filter requests
# sent to remote servers based on the rules defined in the
# 'attrs.pre-proxy' file.
# attr_filter.pre-proxy
# If you want to have a log of packets proxied to a home
# server, un-comment the following line, and the
# 'detail pre_proxy_log' section, above.
# pre_proxy_log
}
#
# When the server receives a reply to a request it proxied
# to a home server, the request may be massaged here, in the
# post-proxy stage.
#
post-proxy {
# If you want to have a log of replies from a home server,
# un-comment the following line, and the 'detail post_proxy_log'
# section, above.
# post_proxy_log
# Uncomment the following line if you want to filter replies from
# remote proxies based on the rules defined in the 'attrs' file.
# attr_filter.post-proxy
#
# If you are proxying LEAP, you MUST configure the EAP
# module, and you MUST list it here, in the post-proxy
# stage.
#
# You MUST also use the 'nostrip' option in the 'realm'
# configuration. Otherwise, the User-Name attribute
# in the proxied request will not match the user name
# hidden inside of the EAP packet, and the end server will
# reject the EAP request.
#
eap
}
} # inner-tunnel server block